Digital power supply case
those 2 choice S400 case and S12D caseare only case, not containing any power supply, S12D case is suitable for RD6006/RD6006W/RD6012/RD6012W case2, there are 2 choice,S400 case and S12D cas, wholesale Digital power .
Digital power supply case S400/S12D and 400W switch power supply for RD6006/RD6006P voltage converter (no RD6006 included) is a one of our Digital power supply case Tools, you can buy Digital power supply case S400/S12D and 400W switch power supply for RD6006/RD6006P voltage converter (no RD6006 included) from foxwellpro.com.
Wholesale Top quality VAS6154, GM Tech2, VCM II For Ford, Handy Baby II Car Key Chip Copier, CDP DS150
images of Digital power supply case S400/S12D and 400W switch power supply for RD6006/RD6006P voltage converter (no RD6006 included)
1, those 2 choice S400 case and S12D caseare only case, not containing any power supply. some picture show installation finished by RD6006 , switch power and case .S12D case is suitable for RD6006/RD6006W/RD6012/RD6012W case
2, there are 2 choice,S400 case and S12D case. For S400 case, you can put AC-DC switch power and RD6006 into this case. for S12D, you only put RD6006.
RD6006 and S400 case assemble instruction: https://drive.google.com/drive/folders/1amKj1B2c2w3NYEQjY7_17ouiZIPQoOwp?usp=sharing
RD6006 and S12D case assemble instruction:https://drive.google.com/drive/folders/155ySRz6Ksvr1JBHdXWVc4mM6cCtqHVoI?usp=sharing
Installation video: https://www.youtube.com/watch?v=RMRuErdv2LM
the option 3 is the 400W switch power supply used for RD6006/RD6006W and Case S400
3, for S400 case, it is just case, not conntaining any power supply, but it is suitable for RD6006/RD6006W and AC-DC 400W 65V switch power supply, you can buy them seperately to assemble easy.
4,for input AC-DC switch power supply, we recommend 400W 65V switch power supply (S400 case leave fix hole size for this version)
Note: Please use the power supply we recommend or some qualified brand power suuply to power on RD6006, Poor quality power supplies may occasionally provide over-voltage when turned on, and the resulting damage must be borne by the customer.
there may be scratches on the surface but it doesn't affect the product performance, please do not be over picky, and if you do mind this, please do not buy this product
5,for S400 case, durning the shipping,maybe the case side wiil be a littledeformation (just like picture ), you can use your hand to ajust, that's ok, if you are mind this , please stop buying.
6.install the device in the right way
2.Product Dimension
3.Accessory List
| NAME | SPECIFICATION | QUANTITY | PICTURE |
| Upper Board | S400 upper board | 1 |
|
| Lower Board | S400 lower board | 1 | |
| Fan | 60mm*15mm | 1 |
|
| Fan power board | 33mm*33mm | 1 |
|
| Screws for fan power board | M3*5*7 | 3 |
|
| Foot pad fixing screws | M3*5*7 | 4 | |
| Screws forfanfixing | Round screw M3*16 | 4 |
|
| Nuts for fan fixing | M3 nut | 4 |
|
| Cables | Brown(9cm)：2 blue(10cm)：1 red(40cm)：1 black(40cm)：1 Temperature sensor connection cable with board:1 | 7 |
|
| Rocker switch | KCD3KCD3 | 1 |
|
| AC power socket | AC-04 | 1 |
|
| Non-slip mat | Φ13*4 | 4 |
|
| switch power supply fixing screws | M4*6mushroomhead | 4 |
|
| Case fixing screws | M3*6 flat head white | 10 |
|
4.Accessory Picture
| A:Lower Board | B:Upper Board |
| C:CaseandAC power socketfixing screws | D:Screws forfan power boardand Mats |
| E:Non-slip mat | F:Switch power supply fixing screws |
| G:Nuts for fan fixing | H:Screws forfanfixing |
| I:Fan power board | J:Rocker switch |
| K:AC power socket | L:Fan |
| M:Cables |
|
5.AssemblyProcedure
5.1 Assembly Preparation
● RD6006/RD6006W/RD6006Pdigital power supply*1, S400case*1,400W65Vswitch power supply*1, DC regulated power supply*1
● Tools, accessory (3 pin plug cable, multimeter, screw driver, test pencil...)
● Proper assembly environment
It is recommend to use a 400W 65V switch power supply as shown below.
5.2 Assembly step
Note:The case material is a bit soft and may be slightly deformed during transportation. If there is a gap during the assembly, please straighten it before assemble it.
①Check the accessories: check if the accessories of S400 are same as accessory list or accessory picture.
②Check RD6006: connect the power cables to the input terminal of RD6006, and then adjust input power supply to 12v/1A to power on RD6006, and set 5V/1A output on RD6006, turn on the output to see if the output is normal.
③Back board assembly: install the rocker switch,AC power socket and fan on the lower board.
④Connect the cables to Switch power supply: connect the brown cable to the (L) terminal, connect blue cable to the (N) terminal, connect yellow-green cable to the (〨) terminal, connect the black cable of the fan board and the output black cable to the (-V) terminals, connect the red cable of the fan board and the output red cable to the (+V) terminals.As shown below.Connect the output
⑤Install the switch power supply
Install the switch power supply on the lower board
⑥Install the board and connect the power cable (dangerous,non-professionals should not operate)
Install the board of temperature sensor extension cable and fan board on the back panel, use brown cable to connect therockerswitch and the live wire (L) of the switch power supply;then use the brown cable to connect therockerswitch and the live wire (L) of the AC power socket;Use the blue cable to connect the neutral wire (N) ofAC power socket and the neutral wire (N) of switch power supply;Use a yellow-green two-colorcableto connect the ground wire (E) ofAC power socket and the ground wire (〨) of switch power supply.Insert the cable of the fan to the fan board as shown below.
⑦Switch power supply test:
Check the wring again and power on the switch power supply, and use test pencil to check the power and insulation status. Then use multimeter to check if the 65V output is normal, then use screw driver to adjust the output of the switch power supply to 68V.
⑧Install RD6006, install the CR1220 battery (prepare yourself) and wifi board (if you order the wifi version), then insert the RD6006 in the right way
⑨Connect the rest cables: connect thegreenterminalto the input of RD6006 and insert the temperature sensor extension cable to the socket on the back of RD6006.
⑩Power on and test
Connect power cable and turn on the switch, the fan start to work.
(Note: Temperature-controlled fan, when the RD6006 is powered on below 40℃, it will work for 3 seconds and then stop, and it will run at low speed below 40℃-50℃, run at medium speed below 50℃-60℃, run at full speed when the temperature exceeds 60℃)
⑪Install the screws of the case
⑫Install the foot pads.
⑬If you want to use the temperature sensor, you just need to insert the cable on the back panel as shown below:
S12D Case Instruction:
Digital power supply case (S12D) assembly instruction
This case is suitable for RD6006/RD6006W/RD6012/RD6012W
Date:2019.10.18
Dear users, thank you for purchasing the digital power supply accessory-metal case produced by Hangzhou Ruideng Technology Co., Ltd. In order to let you know more about the full function of this product, get a better experience and avoid misuse. Please read this instruction carefully before assembly. Keep it for future reference.
1.Notes
● Read this instruction carefully before assembly, if you still have question, please contact us.
Since the assembly process involves voltage that exceeds the human body's safety, non-professionals should not operate, do insulation and protective measures during the assembly process, check the wiring several times for safety, and place the product at a place which children and old people can not get.
● This case is made of cold-rolled steel plate and the surface is sprayed. When assembling and using, prevent it from scratching by sharp objects, and avoid direct sunlight and humid environment.
● Avoid short circuit when assembling, connect the electrode correctly.
● NEVER connect the cables with the power ON.
● Try to avoid vibration and fall.
2.Product Dimension
3.Accessory List
| NAME | SPECIFICATION | QUANTITY | PICTURE |
| Upper Board | S12D | 1 |
|
| Lower BoardS12D | S12D | 1 | |
| Cables | RED：2 BLACK：1 | 3 |
|
| Female Banana Socket | M4*36 | 2 |
|
| Rocker switch | KCD3 | 1 |
|
| Non-slip mat | Φ13*4 | 4 |
|
| Mat fixing screws | M3*5*7 | 4 |
|
| case fixing screws | M3*6 flat head white | 8 |
|
4.AccessoryPicture
| A: Upper Board | B:Lower Board |
| C: Non-slip Mats | D: Screws for Non-slip Mats |
| E: Case Fixing Screws | F: Cables |
| G: Rocker Switch | H: Female Banana Socket |
5.AssemblyProcedure
5.1 Assembly Preparation
● RD6006 digital power supply*1,S12Dcase*1
● Tools, accessory(DC power supply,screw driver)
● Proper assembly environment
Note:The case material is a bit soft and may be slightly deformed during transportation. If there is a gap during the assembly, please straighten it before assemble it.
5.2 AssemblyStep
1. Check the accessories:
Check if the accessories ofS12Dare same as accessory list or accessory picture.
2. Install the female banana sockets and switch:
Please put the female banana sockets and rocker switch on the corresponding position of back board, the red female banana socket is positive electrode and the black female banana socket is negative electrode. Screw the fixing screws.
3. Connect cables
Use cables to connect switch and female banana sockets, and tighten with nuts, the wiring is completed, you can see the final connection below:
4. Install RD6006: install RD6006 on the front side and connect the external sensor.
5. Use 12V/1A DC power supply to power on RD6006, check if the connection succeeds(check the wring before power on)
6. Install the upper board: install the upper board on lower board, and use screws to fix it.
7. There are four Non-slip mats, please use screws to fix them.
