3.Accessory List

5.AssemblyProcedure

5.1 Assembly Preparation

● RD60XXdigital power supply*1, S800case*1,800W switch power supply*1

● Tools, accessory(DC power supply, 3 pin plug cable, multimeter, screw driver, test pencil...)

● Proper assembly environment

It is recommended using a 800W switch power supply as shown below.

5.2 Assembly step

Note:The case material is a bit soft and may be slightly deformed during transportation. If there is a gap during the assembly, please straighten it before assemble it.

①Check the accessories: check if the accessories ofS800are same as accessorieslist or accessory picture.

②Check RD60XX:Adjust input power supply to 12v/1A to power on RD6012, and set 5V/1A output on RD60XX, turn on the output to see if the output is normal.

③Back board assembly: install the rocker switchandAC power socketon the lower board.

④Connect cables to switch power supply: (dangerous,non-professionals should not operate)

Uselongbrown cable to connect therockerswitch and the live wire (L) of the switch power supply; then useshortbrown cable to connect therockerswitch and the live wire (L) of the AC power socket; Use the blue cable to connect the neutral wire (N) ofAC power socket and the neutral wire (N) of switch power supply; Use a yellow-green two-colorcableto connect the ground wire (E) ofAC power socket and the ground wire (〨) of switch power supply.Use two red cables to connect the IN+ of the green terminal and the positive electrodes (+V), and use two black cables to connect the (IN-) of the terminals and negative electrodes (COM). Install the temperature sensor extension board to the back panel.

If you want to use S800 for RD6024, you need to solder the connector to the cables first, then you connect the RD6024

⑤Assemble the switch power supply：Installthe switch power supply on the lower board

⑥switch power supply test:

Check the wring again and power on the switch power supply, and use test pencil to check the power and insulation status. Then use multimeter to check if the output is normal, then use screw driver to adjust the output of the switch power supply to about 68V.

⑦RD60XX assembly：If you have CR1220 battery, pleaseinstall the battery with the positive side facing up, if you have WiFi module, please install it like what shows in the picture. InstallRD60XX to the front side in the correct way, otherwise it cannot be installed properly, we make flame tight to prevent the RD60XX from shaking, if the case is slightly deformed, you can gently bend the case to make itstraight.

⑧Connect the rest cables:insert the external temperature sensor cable, insert the green terminal and sort out the cables.

⑨Install the screws of the case

⑩ Install the foot pads.

⑪If you need to use external temperature detect, you can insert the external temperature sensor cable to be back end of the case, and do final test.

4.AccessoryPicture

5.AssemblyProcedure

5.1 Assembly Preparation

● RD series digital power supply*1, S12D case*1

● Tools, accessory (DC power supply, screw driver)

● Proper assembly environment

Note:The case material is a bit soft and may be slightly deformed during transportation. If there is a gap during the assembly, please straighten it before assemble it.

5.2 AssemblyStep

1. Check the accessories:

Check if the accessories of S12D are same as accessory list or accessory picture.

2. Install the female banana sockets and switch:

Please put the female banana sockets and rocker switch on the corresponding position of back board, the red female banana socket is positive electrode and the black female banana socket is negative electrode. Screw the fixing screws.

1. Connect cables

Use cables to connect switch and female banana sockets, and tighten with nuts, the wiring is completed, you can see the final connection below:

1. Connect the terminals, you can connect the U-shaped plug directly to the green terminal of RD6012/RD6012-W, and you need to cut off one side of U-shaped plug and connect them to the green terminal of RD6006/RD6006-W.

5. Install the RD power supply: install the power supply on the front, and insert the green terminal to the power supply, and then connect the external temperature sensor.