Foxwell NT520 Pro Multi-System Scanner with Free Mercedes Benz Software and Extra Foxwell Benz 38Pin and Extension Cable

Foxwell NT520 PRO Multi-System Scanner Tool for mercedes Benz + 38-PIN Connector

The Foxwell NT520 for MERCEDES is a professional fault diagnosis tool designed specifically for Mercedes Benz vehicles. It is an easy to use, stand alone unit that will have you scanning your vehicle within minutes. Simply, plug it into the OBD II port and the device will boot up with step-by-step instructions. This scanner has a large, easy to read 4 inch color display accompanied by a user friendly interface that requires no additional software. As an added bonus, the scanner is equipped with full OBDII capabilities that allows you to scan all engine readings and engine related trouble codes (check engine light) on ANY vehicle make/model 1996 and newer.(U.S. only) In addition to the common functions listed below, this scanner also has full programming and coding capabilities similar to the dealer mercedes MB STAR tool.

Oil/Service/Brake Service Reset Function

The NT520 allows you to reset Oil,Service, and Brake Lights in a click of a button on supported vehicles. On vehicles where a manual reset is required, the tool will guide you through the full process step-by-step.

EPB Reset Function

Brake Pad / Shoe changes on vehicles equipped with EPB's (Electronic Parking Brakes) MUST be carried out using a Diagnostic Tool to correctly re-calibrate. The NT520 offers you that capability on supported models. De-activate to Service Position - Replace - Re-activate.

SAS Reset Function

The Steering Angle Sensor (SAS) is used to measure the angle of the steering wheel and the speed at which it is being turned. The signal is mainly used by the ABS System as part of it's stability control function but also by other systems such as ride level control and adaptive lighting. A problem with the SAS Signal will cause a fault with any of the systems that use the signal directly, or indirectly.
If the Steering Angle Sensor (SAS) needs to be changed, many vehicle's require the new sensor to be calibrated. The NT520 will allow you to carry out steering angle re-calibration on supported models.

DPF Regeneration or Replacement

Carry out a forced Diesel Particulate Filter (DPF) Regeneration on supported vehicles - this MUST be done by trained personnel. Required when the DPF filter blockage reaches levels where passive or active regeneration is unable to burn off the excess soot. The NT520 is also capable of adapting a new DPF Filter where supported.

Compatible Vehicles

(Please consult wikipedia.org if you are unsure of your body/chassis style, scanner will not work with your vehicle if it is not listed)

mercedes Benz
A Class: 168 , 169 , 176
AMG GT: 190
B Class: 245 , 242/246
C Class: 202*(As of 06/97), 203 , 204 , 205
CL Class: 140*, 215 , 216
CLA Class: 117
CLC Class: 203
CLK Class: 208*, 209
CLS Class: 218 , 219
E Class: 210*(As of 03/97), 207 , 211 , 212
G Class: 461 , 463
GL Class: 164 , 168 , 166
GLA Class: 156
GLC Class: 253
GLE Class: 292, 166
GLK Class: 204
M Class: 163 , 164 , 166 , 292
Maybach Class: 240
R Class: 251
S Class: 140*, 220 , 221 , 222 , 217
SL Class: 129*(As of 09/99), 230 , 231
SLC Class : 172
SLK Class: 170(up to 2001)*, 170(after 2001) , R 171 , R 172
SLS Class: 197
SLR Class: Series 199

our 38 pin multiplexer adapter cable required for these chassis

Foxwell 38-PIN Round Multiplexer Adapter for Mercedes Benz

This multiplexer adapter allows you to connect your Mercedes equipped with the older, round 38 PIN connector to a compatible Foxwell NT520 PRO diagnostic tool.

This connector only works with the following Foxwell models: NT520 PRO, GT80 and GT80 mini.

The Foxwell NT520 PRO scanner is only compatible with this adapter. The standard adapter without the multiplexer does not work.

Foxwell NT520 Car Software List :

Notice: Scanner is shipped with the advertised software make, each additional make is $60

1. Ford ( includes Ford, Lincoln, Mercury vehicles )

2. BMW ( includes BMW , MINI , Rolls-Royce vehicles )

3. Chrysler ( includes Chrysler, Dodge , Jeep vehicles )

4. Fiat ( includes Fiat , Alfa , Abarth, Lancia vehicles )

5. GM ( includes Buick, Cadillac, Chevrolet, GMC, Saturn, Pontiac, Daewoo, Holden vehicles )

6. Honda ( includes Honda, Acura vehicles )

7. Hyundai ( includes Hyundai , Kia vehicles )

8. Land Rover ( includes Land Rover , Jaguar vehicles )

9. Opel ( includes Opel, Vauxhall vehicles )

10. Toyota ( includes Toyota , Lexus, Scion vehicles )

11. VAG ( includes Volkswagen , Audi , Seat , Skoda , LaMBorghini , Bentley vehicles )

12. Aston Martin ( includes Aston Martin vehicles )

13. Ferrari ( includes Ferrari vehicles )

14. Maserati ( includes Maserati vehicles )

15. Mazda ( includes Mazda vehicles )

16. Volvo ( includes Volvo vehicles )

17. Porsche ( includes Porsche vehicles )

18. Benz (includes Mercedes, Sprinter, SMART, Maybach vehicles)

19. Renault (includes Renault, Dacia vehicle)

20. PAS (includes Peugeot, Citroen vehicles)

21. AU Ford(includes Australia Ford Vehicles)

22. Holden(includes Holden vehicles)

Foxwell NT520 Pro Support Lifetime Free Upgrade

1.Please search on official website www.foxwelltech.com to download NT520 client update software

2.Install update clients software and create an Foxwell account ID

3.Please plug the USB to you pc and connected the NT520. meanwhile press “Update” button Enter upgrade mode

4.Use NT520 S/N nuMBer and password register and choose brands software update

5.Wait for the update process finished, the scanner NT520 will be ready to go! we will update to latest version.

Notice: Please turn off anti-virus software when installing, otherwise it will not be able to start software properly

Foxwell NT520 language:
English, Chinese (Simplified), Chinese (Traditional),English, French, Spanish, Dutch, German, Russian, Italian, Hungarian, Portuguese

Features and Benefits
Delicately developed by the most distinguished experts in this industry. Foxwell NT520 Pro is a low-cost handheld scan tool that delivers OE-level diagnosis on all the electronic systems for a single car manufacturer. It does not only include basic the functions such as read & erase code, live date, but also it's capable of advanced functions such as actuation,adaptation coding and programming- ideal for specialist, garages and car enthusiasts.

Available makes are: Acura Alfa Romeo, Abarth Audi, BMW, Chrysler. Fiat, GM Honda, Hyundai, Jaguar, KIA Lancia, Lexus, Land Rover, Maserati, MINI. Toyota，Opel, Rolla-Royce, Scion, Seat, Skoda,Vauxhall, VW, mercedes Benz, Peugeot and more. (Compare with NT510, Mercedes Benz is newly added)

The scanner is shipped with one free software and can cover up to five vehicle makes. More software can be added anytime at extra cost .

Foxwell NT520 Specifications:

Display: Backlit,2.8”TFT color screen
Operating Temperature: 0 to 60°C (32 to 140°F)
Storage Temperature: -20 to 70°C (-4 to 158°F)
External Power: 8 to 18 V provided via vehicle
Dimensions: 200*100*38MM(L*W*H)
Storage Temperature:-20 to 70°C (-4 to 158°F)
Dimensions : 145*94*32MM
Color Box: 220*85*165MM
Weight: 0.9KG
PCS/CTN: 30PCS
Weight/CTN: 27KGS
CTN MEAS: 456*442*515MM

Package includes:

1pc x NT520 Pro Multi-System Scan Tool
1pc x Main 16pin cable
1pc x User’s Guide
1pc x Memory Card
1pc x USB Cable
1pc x Nylon Carry Pouch
1pc x Foxwell Benz 38Pin and Extension Cable